PERANCANGAN ALAT PERAGA DIFFERENTIAL THERMAL ANALYSIS UNTUK ANALISIS TITIK LELEH MATERIAL INDIUM, TIMAH DAN SENG

Authors

  • Fitria Hidayanti Program Studi Teknik Fisika, Fakultas Teknik dan Sains, Universitas Nasional, Jakarta 12520
  • Tri Yulianto Pusat Penelitian Fisika, Lembaga Ilmu Pengetahuan Indonesia, Serpong, Banten 1531
  • Agus Sukarto Wismogroho Program Studi Teknik Fisika, Fakultas Teknik dan Sains, Universitas Nasional, Jakarta 12520

DOI:

https://doi.org/10.31958/js.v8i2.472

Keywords:

differential thermal analysis, the melting point of indium, tin melting point, the melting point zinc

Abstract

The aims this research was to designed a differential thermal analysis props to analyze the melting point of the material. Differential Thermal Analysis props have a furnace with a maximum temperature of 600 ┬░ C. Temperature sensor used is a K-type thermocouple with a measurement range of -200 ┬░ C to 1200 ┬░ C. Controller is used to control the temperature of the furnace is Autonics with digital temperature controller type TK4M. Measurement of the value of the temperature in the furnace using an Arduino Uno microcontroller connected to LabVIEW software via USB. Measurement of the melting point of the material used these props are tested on material Indium (In), tin (Sn), and zinc (Zn) with a melting point 152,50C, 231,50C and 4250C.

Author Biography

Fitria Hidayanti, Program Studi Teknik Fisika, Fakultas Teknik dan Sains, Universitas Nasional, Jakarta 12520

Institut Agama Islam Negeri (IAIN) Batusangkar

 

References

Amy L, Yingwei F dan Russell J. 2010. Solid State Communications 150, 625-627.
Yang H, dkk. 2013. Rare Metal Materials and Engineering 44, 2665-2669.
Balaram K, dkk. 2013. Procedia Engineering 127, 287-294.
Wardoyo S, Munarto R dan Putra VP. 2013. Jurnal Ilmiah Elite Elektro 4, 23-30.
Wismogroho AS. 2013. Studi awal pengembangan calculated-differential thermal analysis (C-DTA) untuk analisa titik leleh material paduan Sn dan Zn. Prosiding Pertemuan Ilmiah XXVII HFI Jateng & DIY. Solo. 23 Maret 2013.
Wismogroho AS dan Wahyu BW. 2013. Jurnal Ilmu Pengetahuan dan Teknologi: TELAAH 30, 7-12.
Nugraha H dan Wismogroho AS. 2013. Perancangan dan sistem monitoring temperatur furnace skala laboratorium berbasis komputer, Prosiding Pertemuan Ilmiah XXVII HFI Jateng & DIY. Solo. 23 Maret 2013.
Wibawa FC. 2012. Penerapan model pembelajaran fisika berbasis proyek untuk meningkatkan hasil belajar kognitif dan keterampilan berpikir kreatif, Tesis. Bandung: Universitas Pendidikan Indonesia.
Artanto D. 2012. Interaksi arduino dan LabVIEW. Jakarta: PT Elex Media Komputindo.

Downloads

Published

2017-03-15

Issue

Vol. 8 No. 2 (2016)

Section

Artikel

License

Copyright (c) 2017 Fitria Hidayanti, Tri Yulianto, Agus Sukarto Wismogroho

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Authors who publish with this journal agree to the following terms:

  • Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
  • Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
  • Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.